? Kinetics considerations concerning the oxidative degradation by photo-fenton process of some antibiotics ? Catalytic wet hydrogen peroxide oxidation of 4-chlorophenol over iron-exchanged clays ? Researches on the negative effects assessment (slugging, clogging, ash deposits) developed at the biomass-coal co-firing ? Contribution to the study of the environmental heritage of a former chemical plant ? Impact of chemicals on derivatives with important therapeutic activity in C...
Autori:
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25376

AbstractAluminum and ferric salts are widely used as coagulants in water and wastewater treatment. They are effective in removing a broad range of impurities from water, including colloidal particles and dissolved organic substances. As well as traditional additives, such as aluminum sulphate ("alum") and ferric chloride, other products containing prehydrolized metal ions such as polyaluminum chlorides are now commonly used. The aim of this study was to develop a model for coagulation/flocculati...
Autori: Avid Banihashemi, Manouchehr Nikazar, , Reza Maknoon
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25230

AbstractThis paper presents experimental and theoretical studies regarding the behavior after heat treatment of an AlCu4Mg1 aluminum alloy with positive effect on corrosion resistance. On the basis of these experiments and the regression data obtained, an analysis regarding the influence of heating parameters on quenching and aging in order to obtain a certain stress was made. Two cases were considered: stress and quenching temperature are fixed and aging temperature was determined; stress and a...
Autori: Adrian Dima, Alina Adriana Minea
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25281

AbstractThe removal of Acid Red 398 (AR398) dye from dye-containing solution using coagulation/flocculation process with polyaluminum chloride (PAC) and Alum was investigated. The effect of different parameters involving pH, dosage of coagulant, initial dye concentration, and bentonite as a natural coagulant aid was examined. According to the obtained results, the optimum pH, at which the maximum removal occurred, was about 4 and 5 for PAC and Alum, respectively. However, PAC performed efficient...
Autori: Maryam Hasani Zonoozi, , Mokhtar Arami
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25335

â€? Photocatalytic properties of titania - fly ash thin filmsâ€? Study of the viscosity of some biodiesel – diesel oil blendsâ€? Aspects refering to technical and leaching properties of the secondary aluminium slags - cement compositesâ€? Studies regarding phenol and 4-chlorophenol sorption by surfactant modified zeolitesâ€? Cu-Ni nanostructured electrocatalysts obtained by electrocodepositionâ€? Molecularly imprinted poly (vinyl alcohol) films for the selective absorption of glycyrrhizinic ac...
Autori: http://www.ecozone.ro/reviste.php?RID=25373

â€? Photocatalytic properties of titania - fly ash thin filmsâ€? Study of the viscosity of some biodiesel – diesel oil blendsâ€? Aspects refering to technical and leaching properties of the secondary aluminium slags - cement compositesâ€? Studies regarding phenol and 4-chlorophenol sorption by surfactant modified zeolitesâ€? Cu-Ni nanostructured electrocatalysts obtained by electrocodepositionâ€? Molecularly imprinted poly (vinyl alcohol) films for the selective absorption of glycyrrhizinic ac...
Autori: http://www.ecozone.ro/reviste.php?RID=25374

Abstract Using slag in steel making represents a challenge for road construction industry and decreasing environment interactions also.Steel making slag wit granulations of < 10 mm, which today have not a sure solution, represents the research object. The technological research solutions have aimed reducing CaO free content in these slugs, and reducing slug fraction with granulationof ...
Autori: Florian Zaman, Mirela Gabriela Sohaciu, Ecaterina Matei, Cristian Predescu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25439

Abstract The paper presents the comparative study regarding the turbidity removal using aluminium sulphate Al2(SO4)3*18H2O and polyaluminum chlorides, Aln(OH)mCl3n-m, commercial name, Sachtoklarr 39, in water treatment plant from Covasna City. The parameters that influence the treatment process and the efficiency of turbidity removal were studied. The water characteristic parameters of Basca Mare and Covasna rivers - the two sources of water alimentation for Covasna water treatment plant were...
Autori: Daniela Simina Stefan, Cristina Costache, Viorica Ruxandu, Monica Balas, Mircea Stefan
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25462

Abstract Application of ozone is known to yield favorable results in purification of phosphate plant water from elemental phosphorus, in treatment of water of alkali aluminate solutions of aluminum plants, in decontamination of cyanide-containing waste water of enrichment plants, and so on. It has been proved that halogen-containing compounds, most of which have mutagenic properties, and some of which are carcinogenic to humans, are formed when water is treated with chlorine. Conclusions made...
Autori: Irina Dumitriu, ,
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25483

Abstract The purpose of this work is to investigate the secondary Al slag (SAS) relating to its technical and environmental properties and, as consequence, to its compatibility with Portland cement matrix. This study may be a contribution to establish of SAS potential valorization as secondary raw material (SRM) in low strength cement matrix composites, as construction products. DRX mineralogical analyses revealed that SAS includes transition alumina compounds, especial boehmite. The hydrati...
Autori: Maria Gheorghe, Nastasia Panait, Romanita Teodorescu, Maria Roman
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25498

Abstract In the paper is analyzed the possibility of using some industrial wastes for obtaining new building materials. From the industry or from the power station a lot of by-products or wastes have resulted and their storage is a big problem for the environment. In the building material industry a part of these wastes can be used in different ways: for replacing the cement, as addition in concrete, as component of cements, in the mixture of polymer concrete, etc. In the present investigati...
Autori: Marinela Bărbuţă, Nicolae Taranu, Maria Harja
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25525

Abstract The slags are an important waste and by-products of metallurgical industry. The present paper summarizes results obtained from physical and chemical analyses on metallurgical slag provided from S.C. ?Mittal Steel Galati? S.A. The physical structure and gradation of granulated slag depend on the chemical composition of the slag, its temperature at the time of water quenching, and the method of production. The following mineralogical components were noticed through bypowder X-ray diffr...
Autori: Maria Cioroi, Licuta Nistor Cristea, Igor Creţescu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25588

? RESEARCH ON NaCl SALINE AEROSOLS I. NATURAL AND ARTIFICIAL SOURCES AND THEIR IMPLICATIONS ? DECISION SUPPORT MODELS FOR SOLID WASTE MANAGEMENT ? AN OVERVIEW ? POLICY AND STRATEGY FOR IMPROVING SUSTAINABLE SOCIAL DEVELOPMENT PROGRAMMES ? APPLICATION OF SHALLOW POND SYSTEM USING WATER HYACINTH FOR DOMESTIC WASTEWATER TREATMENT IN THE PRESENCE OF HIGH TOTAL DISSOLVED SOLIDS (TDS) AND HEAVY METAL SALTS ? TRENDS OF THE COMMUNITARIAN COHESION POLICIES AND ADVERTISING FOR EC...
Autori:
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25658

Slag-Fly Ash Based cementitious material materials with high volume of fly ash and slag and less cement clinker was prepared, with low water requirement, well fluidity and with high strength, and can be used to the preparation of High Performance Concrete (HPC). When the W/C is 0.36, the 28d compressive strength is 58.93 Mpa, 28d flexural strength is 14.26 Mpa. By XRay diffraction analysis (XRD) and Scanning Electron Microscope (SEM) analysis, the results show that main materials in grinded samp...
Autori: Chenghong Fu, Wen Ni, Hui Wu, Mingyang Tianhttp://www.ecozone.ro/reviste.php?RID=25708

Abstract:The operation of solar air heat collectors consists in a sequence of transient regimes, being conditioned by the availability in timeof the solar resource. This paper presents the results of an experimental research on transient regimes of two types of solar air heatcollectors. The absorbers of the collectors have different configurations and are made of different materials. One collector is acommercial passage air collector with the absorber made of aluminum. The other collector is an ...
Autori: Adrian Ciocănea, Andrei Dragomirescu, Sanda Budea
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25731

Abstract:This study aimed to assess the coagulation performance using simple aluminum sulfate (Alum) and pre-hydrolyzed polyaluminumchloride (PACl) coagulation agents by conventional global parameters, i.e., turbidity and organic matter expressed by totalorganic carbon (TOC) and chemical oxygen demand (COD), and non-conventional spectrophotometric parameters.Non-conventional spectrophotometric parameters, expressed as absorbance recorded at different wavelengths, i.e., A254, A280,A365, allowed d...
Autori: Florica Manea, Georgeta Burtică, Ilie Pisoi, Smaranda Masu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25777

Abstract: In this study, decolorization and degradation of aqueous nickel phthalocyanine reactive dye solutions was comparatively studied by electrochemical methods, such as electrocoagulation, electrooxidation and electro-Fenton processes. In the electrocoagulation process with aluminum electrodes the colored aqueous solutions containing 100 mg/L nickel phthalocyanine and 6 g/L NaCl were treated at initial pH 7.5 and applied current densities of 5, 10 and 20 mA/cm2, where fast and 100% decolori...
Autori: Achilleas Christoforidis, Dimitrios Marmanis, Evgenia Valsamidou, Konstantinos Dermentzis, Konstantinos Ouzounis
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25804

Abstract:The paper presents the results of a study carried out using the Artificial Neural Network (ANN) for prediction the coagulation/flocculation process of suspended solids in water treatment plant (WTP). In this research 5 kinds of Poly Aluminum Chloride (PAC) as coagulant were used to examine the impact of coagulant kinds, PAC dosage and influent turbidity for removal of suspended solids. Determination of optimal coagulant doses is vital, as insufficient dosing will result in undesirable t...
Autori: Gagik Badalians Gholikandi, Mohammad Delnavaz, Reza Riahi
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=25806

AbstractThe slag and the ash, resulted after the lignite burning in the boilers of Thermal Power Plant located at Timisoara South(Romania), are hydraulically evacuated at the storage facility for slag and ash near village Utvin. Fine ash from compartments ofslag and ash deposits that are not covered by water can be driven by air currents, causing pollution. After admission of Romaniain European Community, the rules for environmental protection are strictly applied. This paper presents the review...
Autori: Emilian Stefan Valea
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26081

Abstract Waste recycling represents a very significant issue for the protection of our environment. Large waste quantities (slag and ashes) are products of the coal extraction industry and its subsequent combustion in thermal power stations. The possibilities of obtaining crystallized glasses in the CaO-Al2O3-Fe2O3-SiO2 system by introducing in the raw materials mixture ashes from Mintia Deva thermal power station have been studied. The physical and chemical characterization of the...
Autori: Firuţa Goga
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26121

AbstractWashing black aluminum (Al) slag to obtain soluble salts is an important stage of the smelting slag treatment at technologicalprocess. This process is used to recover Al as a coagulant for water purification. This research aims at establishing the optimalconditions for washing (e.g. temperature (T), solid: liquid ratio (S : L), time, the recirculation waters in the system). The goal ofresearch was to determine: a) the removal with maximum efficiency of the soluble salts from black Al sla...
Autori: Romanita Teodorescu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26243

AbstractThis paper continues the previous investigations regarding the technology for the Aluminum (Al) recovery as Al sulfate fromblack Al slag. Leaching is the next compulsory step in the Al extraction process. The paper studies the influence of mothersolutions´ (MS) recirculation resulted from the process within the system over the quality of Al sulfate and the siliceous residue(R) and, the aluminum nitride (AlN) hydrolyses in the leaching process. The optimum parameters determined are: *the ...
Autori: Romanita Teodorescu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26250

AbstractThe purpose of the undertaken research work is to degrade the biopolymeric pigments present in the distillery spentwash. This isdone by direct electro-oxidation using iridium oxide coated titanium mesh as catalytic anode. The effects of current intensity,dilution, pH and time of electro-oxidation were studied. The combined effects were analyzed using Box-Behnken design foroptimization and statistical analysis. The rate constant for first order electrochemical kinetics relating the rate c...
Autori: R. Krishna Prasad
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26253

AbstractWorldwide, waste materials are produced as a by-product of industrial manufacturing and placed in storage areas. One of the waste materials is filter cake (FC). FC is formed during the infiltration of cooling water in steel factories. The main aim of this research is determination of optimum usage of FC in the production of impermeable layer on ground by using fuzzy model approach. Because of this, in the study, FC as a waste material was hardened with cement and an impermeable layer was...
Autori: Ä°lker Bekir Topďż˝u, Murat Karacasu, Tayfun Uygunoğlu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26288

AbstractSecondary aluminium production inherently generates significant amounts of slag of variate composition and including dangerous compounds. Consequently, a care treatment of the resulted slag is imperatively necessary for preventing the environment pollution and for recovering valuable materials even if present in low amounts. The aluminium recovering procedure is based on a chemical and hydrometallurgical slag treatment, leading to the technical grade aluminium sulphate (AS), possible to ...
Autori: Carmen Tociu, Cristina Maria, Elena Diacu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26295

AbstractA new cell design which makes an efficient use of the cathodically evolved H2 to improve the mixing efficiency and thefloatation ability during electrocoagulation was used to remove dyes from waste solution. In this study, the decolorization andCOD reduction of colored solutions containing reactive and basic dyes by electrocoagulation was investigated using aluminumelectrodes in a batch mode. The effect of operating parameters such as current density, initial dye concentration, NaClconce...
Autori: El Sayed Zakaria El Ashtoukhy
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26303

AbstractThe paper compares the electrocoagulation performance during the removal of Acid Brown 14, Acid Yellow 17, Acid Blue 113and Acid Black 172 dyes from aqueous solutions. For this purpose, pH changes and effectiveness of main parameters includinginitial dye concentrations and current densities for the selected dyes were examined. In addition, effluent turbidity, energyconsumption and amounts of released aluminum were also investigated. The present work shows that Acid Yellow 17 removaleffic...
Autori: Mahsa Taheri, , Mokhtar Arami
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26310

AbstractThis paper discusses some environmental problems caused by the mine waste from the Copper Mine Bor in Serbia. The CopperMine Bor and the Smelter generated about 2x109 tones of waste materials, located in the vicinity of the Bor. They cover mining,flotation tailings and smelting slag wastes. The existing mine waste have been formed during a hundred-year-old of mining andmetallurgical activities in Bor. Also, new quantities of wastes (up to ten thousand tones) have been produced daily by u...
Autori: Jovica M. Sokolović, Novica Milosević, Rodoljub D. Stanojlović
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26334

AbstractMost studies exploring the contribution of the mycorrhizal symbiosis to plant metal tolerance focus on plant-metal uptake anddisregard metal effects on the symbiotic fungi. We examined the tolerance of the model arbuscular mycorrhizal fungusRhizophagus irregularisto Al and Pb in vitro cultures with transformed carrot (Daucus carota L.) roots that exclude theinterference of other microbiota. We studied the development of roots and external mycelium of R. irregularis in monoxenic andaxenic...
Autori: Mayra E. Gavito
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26516

AbstractPetroleum tanker trucks are integral vehicles for delivering fuel and other petrochemical products from place to place and must becleaned regularly. Pressure washing with hot or cold water serving to remove oil and filth from the tanker truck container,produces oily waste water with an oil concentration of about 300-500 mg L-1 which, according to environmental standards andregulations worldwide, must be disposed of and treated properly. In the present paper an integrated electrochemical ...
Autori: Konstantinos Dermentzis
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26520

AbstractThis study aims to understand the acid-leaching behavior of metals from 2 to 4 mm waste printed circuit boards (WPCBs)containing 22.0% ą 1.1 Cu, 6.7% ą 0.2 Ca, 0.68% ą 0.02 Sn, 0.59 ą 0.01 % Pb, 2.71% ą 0.08 Al, 0.22% ą 0.01 Fe, etc..Copper leaching was increased for sulfuric acid concentrations up to 1.2 mol/L and hydrogen peroxide concentrations of 10.0vol% for a pulp density of 100 g/L at 50°C over 4 h, whereas for the same concentrations of sulfuric acid and hydrogen peroxidecopper l...
Autori: Manoj Kumar
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26566

AbstractThe incorporation of phosphorus (P) into sediments and the changes in its bioavailability under intermittent P input and sedimentresuspension conditions were investigated via laboratory experiments. The sediments were disturbed daily for 10 min and thenallowed to settle for 1430 min after each disturbance to simulate the intermittent sediment resuspension conditions. The removalof soluble reactive P from the overlying water under sediment resuspension was greater than that under static c...
Autori: Li Dapeng
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26567

Abstract In this study, the COD removal of Azithromycin from synthetic wastewater (produced to have a composition similar to industrial wastewater) using a Fenton-like (Fe°/H2O2) system in combination with coagulation has been investigated. Chemical oxygen demand (COD) was selected as the main parameter to assess treatment efficacy in the current study (COD° = 390mg/Lequivalent to 200mg/LAzithromycin). First, the coagulation process was carried out on the synthetic wastewater and the...
Autori: Ahmad Reza Yazdanbakhsh
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26586

Abstract The performance of electrocoagulation (EC) process, a non-specific electrochemical technology, was investigated for the removal of carbamazepine (CBZ), an antiepileptic drug, from water. Experiments were carried out in synthetic wastewater in a batch cell. The respective influences of some key process parameters were studied, such as mixing conditions, initial pH, and current on aluminium electrodes. Experimental results showed that a CBZ removal efficiency of 62% was observed under...
Autori: Tania Yehya
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26683

Abstract This paper discusses end-of-life (EoL) modeling issues in Life Cycle Assessment (LCA), through the application to a domestic cooker hood. Two EoL approaches are applied and discussed, namely the avoided burden and the one recommended by the Product Environmental Footprint (PEF) Guide, presently under testing. While no case studies on PEF application have been published yet, to the best of our knowledge, the scientific community is questioning the robustness and relevance of some me...
Autori: Francesca Reale
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26790

Abstract Recently several innovative suggestions on how industrial wastes can be utilised in new products have been presented in literature, e.g. as filler or additives in concrete, incorporated in ceramic materials to produce glass-ceramics and pavement construction. In this work, metallurgical materials from secondary aluminium scrap processing and glass waste derived from treatments of packaging and fluorescent lamps were considered for fabrication of new ceramic materials using powder te...
Autori: Rosa Taurino
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26794

Abstract The objective of this paper is to propose an optimal path for a circular economy strategy of Aluminum Corporation of China (CHINALCO) by constructing a circular economy evaluation model. Based on CHINALCO’s resource circulation and the regularity of material balance, and by depicting the value information in the process of resource input, consumption, output and waste, we build a comprehensive evaluation model for the enterprise circular economy - a resource value flow equatio...
Autori: Fei Xiong
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26815

Abstract The aim of this paper is to assess the chemical and mineralogical composition and the leaching behavior of the electric arc furnace slags (EAFS) in order to improve their management by identifying suitable reuse options in different fields. The chemical and mineralogical composition of slag varies from one type of steel to another, from one technological stage to another and from one steel plant to another. In order to minimize the slag quantities disposed in the slag dumps one has ...
Autori: Dana-Adriana Iluţiu-Varvara
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26835

Abstract Ash resulting from wood combustion constitutes a waste disposal problem to facility owners. The use of ash fertilizer or soil amendment could provide nutrients for agriculture if its nutrient content is adequate and it does not contain harmful amounts of heavy metals. The recycling of nutrients bound in ash would provide an inexpensive solution to waste problem. In our study, we aimed to characterize ash and clinker resulted from incineration of oak waste resulted from wood industry...
Autori: Ioan Oroian
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26885

Abstract Trace metal elements commonly exist in drinking water. Excessive exposing on them may result in lots of health problems. This paper mainly focuses on the accumulations of Cu2+, Cd2+, and Pb2+ in drinking water supply networks with amorphous Al(OH)3 formation. The effects of pH, water flow rate, and metal element contents were investigated at laboratory bench scale. It was found that chemical adsorption mainly occurred at pH > 7.0. Suspended Al(OH)3 showed a strong adsorption capa...
Autori: Wendong Wang
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26906

Abstract This study investigated the feasibility of electrocoagulation (EC) process on the treatment of palm oil mill effluent (POME). The effect of several parameters namely initial pH, current density, stirring speed and operating time on removal efficiency of total suspended solids (TSS) and chemical oxygen demand (COD) were investigated. The experiments were conducted batch wise using 400 mL of the POME per batch and pair of aluminum electrodes immersed in the reactor. At optimal initial...
Autori: Firdaus Ghazali
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26914

In this work, coagulation features and characteristics of dissolved organic matter (DOM) in combined sewer overflow (CSO) wastewater were investigated. Ferric chloride (FeCl3) and polyaluminum chloride (PAC) were employed in the coagulation process. Results showed that both FeCl3 and PAC are effective in removing turbidity and total phosphorus (TP). Removal efficiencies were all above 90% when dosages were reasonable. Chemical oxygen demand (COD) removal efficiency was between 60% and 70%. T...
Autori: Wei-gang Wang
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26931

In the context of sustainable development, focus must be set on reasonable use of natural and energetic resources, which is a real must at present. Besides these, material and informational resources add up to give the full picture of sustainable development resources. The paper introduces a valid solution of powdery waste recycling into pellets for the steelmaking industry. The pellets are obtained from powdery wastes (steel plant dust, red sludge, lime dust, dolomite waste, waste limestone,...
Autori: Ana Virgina Socalici
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26944

Ferric sulfate and aluminum sulfate were applied to stabilize the available arsenic in solid waste residue (SWR) from the organic arsenic industry, previously pretreated by the semi-solid Fenton process. NaOH, Ca(OH)2, and MgO were introduced to adjust the matrix pH. Toxicity characteristic leaching procedure (TCLP), synthetic precipitation leaching procedure (SPLP), and sequential extraction procedure (SEP) were carried out to evaluate the effect and difference on the fixation treatments of ...
Autori: Li-Fang Hu
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26956

Waste recycling in steel industry by turning grain-size and powdery waste into pellets is a must now more than ever for economical motivation, in order to save raw materials and also for ecological reasons, as it leads to a cut down in the quantity of dumped waste. Industrial practice offers processors various technologies of waste recycling (agglomeration, briquetting, pelleting, mechanical mixture). The optimal variant should be chosen according to waste type, its content of useful elements...
Autori: Ana Virgina Socalici
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=26968

In this research, Response Surface Methodology (RSM) was employed to optimize five operating variables including initial pH, current, reaction time, initial hexavalent chromium concentration and dosage of polyaluminum chloride as a coagulant for the removal of hexavalent chromium and its relative operating cost by electrocoagulation process. Central Composite Design (CCD) was applied for the optimization process. The results showed that increase of polyaluminum chloride dosage was beneficial for...
Autori: Sepideh Sadeghi
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27230

The present study shows the results of the chronic test in evaluating the response of lumbricidae under the action of different concentrations of Alleato 80WG. The earthworm samples were taken from a plot of land cultivated with maize. Survival, biomass and aluminum content bioaccumulated in earthworms have been analyzed. Five replicates were carried out for each experiment. The survival rate showed maximum values (100%) for V5 (control sample), and (200 mg kg-1) (p=1) for V4. The other three co...
Autori: Gheorghiţa Brînzea
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27334

Three modified bentonites, hydroxy-aluminum pillared bentonite (Al(OH)-Bent), cetyl trimethylammonium bromide modified bentonite (CTAB-Bent), and both cetyl trimethylammonium bromide and hydroxy-aluminum modified bentonite (Al(OH)-CTAB-Bent) were prepared and characterized by Fourier transform infrared spectroscopy (FTIR) analysis. Batch experiments were conducted on the adsorption of phenol at different temperatures, pH and initial concentration. The results indicated that adsorption capacity o...
Autori: Xiping Luo
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27481

An apatitic calcium phosphate gel (HaG) was elaborated and used to treat municipal wastewater in a physicochemical cycle prior to the standard biological degradation process. Preliminary laboratory batch experiments outlined the kinetics of heavy metal sorption by monitoring the concentrations found in filtered fractions as a function of treatment time. On site experiments were performed in a municipal wastewater treatment plant by derivation of real wastewater into an experimental tank. In this...
Autori: Nathalie Lyczko
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27488

Papermaking tobacco sheet wastewater exhibits high content of fine suspended solids (SS), intensive color and low biodegradability. Through the process of electrocoagulation (EC) using aluminum anode and stainless steel net cathode, the performance of wastewater treatment and the evolution of the main components in wastewater were examined. Maintaining the pH of wastewater, with 40 mA/cm2 of current density, 2.5 g/L of NaCl for a reaction of 6 min duration, 66.1% of the total chemical oxygen dem...
Autori: Xiangjuan Ma
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27509

Thin-film transistor liquid-crystal display (TFT-LCD) waste glass can be used as a raw material for producing geopolymers, because it contains large amounts of silicon and aluminum in its amorphous structure. The setting time and compressive strength were evaluated to determine the quality of the geopolymer product with various amounts of nano-SiO2 (0%–3%) and TFT-LCD waste glass replacement (0% - 40%). The microstructures of the samples were characterized using mercury intrusion porosimet...
Autori: Kang Gao
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27634

Pyrometallurgical recycling of lead from spent batteries entails secondary waste fractions generated in the blast furnace as iron stone and lead slags. For further purification of both fractions, hydrometallurgic processing is proposed. This paper focuses on purification of iron stone, in view of recovering metals (mainly lead) and of producing decontaminated iron stone fit for further recycling. The results demonstrate that iron stone is mainly composed of iron and lead; copper, zinc and antimo...
Autori: Bart Van der Bruggen
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27642

The paper describes the main results from a study of cement bound mixtures for road foundations with the aggregate matrix consisting of industrial wastes, i.e. foundry sands (FS), electric arc furnace (EAF) steel slags and bottom ash from municipal solid waste incineration (MSWI), combined in five different proportions. The laboratory investigation involved a preliminary analysis of the chemical, leaching, physical and mechanical properties of the industrial wastes, followed by a mechanical char...
Autori: Marco Pasetoo
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27645

In this research, effects of in-line coagulation on permeation flux (PF), flux reduction (FR) and total organic compound rejection (TOC R) of synthesized mullite-allumina MF ceramic membrane (with 50 wt % alumina content) during treatment of synthetic oily wastewater in were investigated. Four coagulants ((ferrous chloride (FeCl2.4H2O), ferrous sulphate (FeSO4.7H2O), aluminum chloride (AlCl3.6H2O) and aluminum sulphate (Al2(SO4)3.18H2O)) plus equal concentration of slaked lime in form of calc...
Autori: Mohsen Abbasi
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27659

The Silicon wafer plays an important role in modern electronic products. During the production of Silicon wafer, a large amount of scrap Silicon wafer is generated. The necessity for it to be recycled and recovered is of vast importance since the metal Silicon (Si) is the major by product. Besides Silicon, the wafers also contain a small quantity of Copper (Cu) and Aluminum (Al), that are considered as minor elements during the recovery process of the Silicon wafer production. Therefore, in o...
Autori: Ching-Hwa Lee
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27660

This paper presents an assessment of the toxic compounds released from metalworking fluids (MWFs) used in aluminum solid waste processing and from aluminum slag landfills, and their impact on environmental quality and human health. The mean concentrations of dust, oil mist, aldehydes, volatile organic compounds (VOCs) released from metalworking fluids were determined in machine shops. The exposure in machine shops was quantitatively dominated by VOCs, whose concentrations varied in the range...
Autori: http://www.ecozone.ro/reviste.php?RID=27677

The aim of this study is the treatment of liquid effluents from a petroleum industry (NAFTAL /Algeria) by an electrochemical treatment process (electrocoagulation). The electrocoagulation has proved to be useful for the treatment of wastewater, but in order to enhance its ecological characteristic we found it would be essential to carry out our experiments with ecological energy derived from a photovoltaic solar module, which would contribute to sustainability objectives. The electrocoagulation ...
Autori: Kahina Ighilahriz
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27679

In this paper, the typical measurement techniques and production procedures defined in the UNI-EN guidelines for ceramic manufacture are taken into consideration to evaluate the properties and the characteristics of the bricks produced by using a mixture containing cubilot slag. The results of the experimental tests demonstrate that these measurement techniques are not enough to define the safety of the waste bricks. Up to now, UNI-EN guidelines for ceramics do not define crystallinity measureme...
Autori: Domenico Luca Carni
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27787

The construction sector has evolved a lot over the last few years promoting the design and manufacturing of innovative and environmentally sustainable materials and products. In accordance with European and national guidelines, with a growing awareness of environmental issues several experiences are showing the interest of companies to qualify their products as green and environmentally sustainable. In the European context many directives have been introduced which, among their themes, speak of ...
Autori: Marco Migliore
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27806

Air cooled and water cooled slag samples were obtained from a demonstration plasma gasification / vitrification unit. The leachability of the major heavy metals present (Cr, Cu, Mn, Fe, Pb and Zn) in both the air cooled and water cooled slag when in contact with acidic solutions was investigated under different temperature, stirring and contact time conditions. Water cooled slag showed better resistance to heavy metals leaching. The vitrification process immobilised Cr and Pb. The leachabilit...
Autori: Konstantinos Moustakas
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=27882

This paper discussed the results of studies regarding metal ions distribution in water, sediments, aquatic plants and different tissues of fish from Snagov Lake, Romania, a natural lake situated 25-30 kilometers north from Bucharest, the capital of Romania. The concentration of several metal ions (Li, Ba, Al, Pb, As, Se) was measured in three points of the lake, namely receiving-input, middle and discharging-output ponds. The samples were collected during spring time from water, sediments, Ce...
Autori: Daniela Simina Ștefan
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=28010

Dairy wastewater has been a major environmental concern because of massive effluents characterized by high pollution load. This study reports the influence of initial pH (pHi), residence time (τ) and elapsed time (t) on the %COD removal (Y1) and specific energy consumed (kWh per kg of COD removed, Y2) for real dairy industry wastewater treatment in continuous stirred tank electrochemical reactor (CSTER) using aluminum electrodes. Central composite design (CCD) was applied for designing th...
Autori: Poonam Kumari
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=28011

Slags are the main by-products from steelmaking cycle, which are currently recycled inside the steel industry as well as in other sectors with significant environmental and economic benefits. As in Italy slags application is not yet allowed in agriculture, the paper aims at evaluating the technical and economic feasibility of a slag treatment plant, to obtain a product to be sold in the fertilizer market as soil amendment. A preliminary assessment of the fate of some trace metals (Cr, V, Sb a...
Autori: Teresa Annunziata Branca
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=28012

The valorization of a metallurgical waste (i.e., an iron-rich slag) as raw material for the fabrication of high hardness glass-ceramics using differential thermal analysis, X-ray diffraction, X-ray fluorescence and scanning electron microscopy was investigated. The melting of the slag was aided by the addition of waste glass cullet (WGC) and the vitrification field of this system was investigated. The non-isothermal crystallization kinetics of the parent glass with the highest slag content was s...
Autori: Erika Iveth Cedillo-GonzĂĄlez
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=28168

Impregnation of aluminium ion onto silica gel (SG) surface (Al/SG) is to increase the adsorption capacity of an anionic dye such as Indigo carmine (IC). The impregnation was carried out using wetness impregnation. The change of the functional group was evaluated by FTIR, crystallinity was determined using XRD, surface morphology were studied by SEM-EDX, while surface area and pore size using N2 gas adsorption-desorption analyzer. Meanwhile, the best of IC adsorption condition onto SG and Al/SG ...
Autori: Yudi Aris Sulistiyo
ISSN: 1843 - 3707
http://www.ecozone.ro/reviste.php?RID=28253